Flight Controller F3 Sp Racing

SP RACING F3 FLIGHT CONTROLLER ACRO VERSION

Racing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performance based on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU.
The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you’re into FPV racing,
acrobatic flying or aerial photography it’s perfect.

Features

• No compromise I/O. Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!

• On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork ( Deluxe).

• Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and faster ARM-Cortex M4 core.

• Stackable design - perfect for integrating with OSDs and power distribution boards.

• 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via sidemounted connectors.

• Full support for OneShot ESCs for easy PID tuning and a sharper response.

• Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required(built-in).

• Dedicated output for programmable LEDs - great for orientation, racing and night flying.

• Dedicated I2C port for connection of OLED display without needing flight battery.

• Battery monitoring ports for voltage and current.

• Sonar support for precision low-altitude hold.

• Buzzer port for audible warnings and notifications.

• Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

• Symmetrical design for a super tidy wiring.

• Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.

• Barometer mounted on the bottom of the board for easy wind isolation.

• Loop times up to ~2x as fast as previous-generation STM32F1 based boards.

• Configuration of the flight controller via a cross-platform GUI (Windows/OSX/Linux).

• Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.

• Available in Acro and Deluxe versions.

Specifications:

• STM32F3 CPU

• High-Capacity Flash (Acro and Deluxe)

• MPU6050 accelerometer/gyro

• MS5611 barometer (Deluxe only)

• HMC5883 compass (Deluxe only)

• MicroUSB socket

• 4x 4pin JST-SH sockets (I2C, SWD, 2xUART)

• 2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)

• 8x 3pin though-holes for pin headers for ESC/Servo connections

• 2x 4pin though-holes for pin headers for 2x serial ports

• 2x 2pin though-holes for pin headers for battery voltage and buzzer

• 36x36mm board with 30.5mm mounting holes

Software
The SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers and community. No more out-of-date wiki pages and second-hand information.Ensure you reference the manual that is appropriate to your firmware version.

Failure to adhere to these warnings will void your warranty and destroy your flight controller.

• Observe polarity at ALL TIMES. Check and DOUBLE CHECK before applying power.

• POWER OFF before unplugging, plugging in or making any connections.

• Connect only one SOURCE of power to the VCC pins / Do not connect more than one source of power to two or more of the VCC pins. e.g. If you are using ESCs with BECs then remove the center RED wire from all but one ESC connector.

• Do not connect GND, VCC or 3.3v to each other (short circuit).

• Do not connect GND, VCC or 3.3v to any inputs or outputs unless specifically stated.

• Do not connect any input or output to any other input or output unless specifically stated.

• The 3.3v supply is for low-current use only. 100mA MAX.

• Do not allow dirt/dust/glue/etc into the pressure sensor (barometer).

• Keep magnets away from the flight controller.

WARNINGS

• Follow the advice below for best performance and long-life of your flight controller:

• Apply resin/glue to reinforce JST-SH connectors - helps if you crash your aircraft.

• Using an enclosure/box for the flight-controller is recommended.

• Install open-cell foam under the pressure sensor - sandwich some between the FC and frame.

• Route motor/battery wires as far away from the compass sensor (magnetometer) as possible.

• Only install the BOOT jumper pins if you need them.

• Using color coded pin headers is recommended (not supplied), especially for VBAT headers.

• Do everything you can to prevent vibrations reaching the accelerometer/gyro sensor.e.g. balance props, motors and secure everything

Variations
Acro: Standard model for racing/acro flying.
Deluxe: Additional sensors for altitude and direction.

Please have a double check of all the qty of items/or individual items when the package is delivered. If any of the qty of ordered items / individual item is missing please inform us for the same withing 24 hrs of receiving the package at:havochobby@gmail.com with SUBJECT:REFERENCE TO ORDER NUMBER.

Due to the nature of hobby, we DO NOT provide any kind of warranty/guarantee for any kind of products sold at www.havochobby.com /.in (HAVOC HOBBY).

Although we assure you all of the products are maintained through a strict QC from manufacturer itself. If you have any technical query after your purchase, you can directly call us or WhatsApp us on (+91) 9535545654. We will try our best to solve the query for the same.

For Cancellation of order please refer to our CANCELLATION POLICY.

In the event of product Dead on Arrival or due to manufacturing defects from the factory itself, the defects to be notified to our team through email: havochobby@gmail.com with SUBJECT: REFERENCE TO ORDER#<NUMBER> DOA within 24 hrs of delivery of the product. In case of manufacturing defects OEM support will be provided to the buyer as far as possible, depending on our contract with the OEM. In case the claim is made after 24hrs HAVOC HOBBY does not hold any responsibility for any of the products.

My product is completely working but of no use to me will HAVOC HOBBY accept return?

• HAVOC HOBBY may exchange item only if the packaging is not broken and provided the customer has informed us within 24 hours of receiving the items on email: havochobby@gmail.com                     Phone/WhatsApp: (+91) 9535545654 . If any of these criteria are not matched HAVOC HOBBY is not liable to exchange such items.
• We urge customers to select products properly while ordering. If for some reason we do provide a Refund it will be in form of Coupon Codes only for next purchase.
• If the RETURN criteria are accepted by HAVOC HOBBY customer will arrange a return Shipment costs & arrangements for sending back the items to us. We will check the items thoroughly which can take up to 7-10 working days then only we can conclude for coupon code for next purchase or the item will be sent back to customer.